Hi had a lot of work in my job found one more what was wrong with the car thanks to Carl my carburettors had no springs when i got the car but they have to have springs, because the engine is a TD engine now I know why the car had problems in the past now I can play with the power and the engine doe...

Hi look to my blog here Mg TA 1932 and you will see what could happen, there are a lot of pictures if you get all parts out without any problems then you can make one side in one hour but if you have problems .... i couldn t get out one half shaft, the car came with three new hlf shafts, i think the...

Hi Duncan
have read this before and done it
;-)
you will see it
THX

Sorry did nothing for the last 3 weeks made some wood for the fire next winter ;-) felled three trees the last days in February were so nice but I couldn't drive the TA because no insurance from the first 01.03 I could drive, but cold and rainy next weekend I will have some time for the last works e...

just done it ;-)
one side it was difficult to get the hub out
llo to my blog

Hello the TA is back in his garden garage almost all done, just need to grease all joints next step is the carburettor my master will overhaul the linkage for the throttle valve so I have removed everything and roughly cleaned the housing. Now I'm going to clean all the parts, polish the brass rods ...

Hithe best side in the web where it is explained how you can make it with one on-off-on switch is here https://www.dkw-f5.de/werkstatt/licht-blinker-und-winker/winker-blinker-teil-1/ With this information I made my own system and I use the switch in the position of the fog lamp switch, I don t have ...

Hi My steering had the needle bearing when I got it 6 years ago, the second steering I have I got 4 years ago from the bay The new sector doesn t fit this steering, so I use the steering with the needles I sl see in spring how it will work I can change to the one without the bearing Just driven out ...

Sorry, I had some problems with the brake line, I had done the bleeding on my own, so I didn't see that there were a few spots that weren't tight. so i didn't have enough brake fluid and had to order some, this morning i did the rest of the work and drove out of the basement garage, before I drove u...

got all the parts from the Octagon Club this evening, tomorrow after work I can continue with the car. I hope to get it out of the basement this weekend. the car will now have a draught excluder around the steering and teh clutch and break pedal also i will change the old brake hose in the back i ho...

there was a discussion in the mgexp.com forum and also once in ttypes.org
was just for fun to make it on my lathe,
waiting for parts ;-) Pastime
but it is actually easier to install
you can install the BMC completely
disconnect the connection, screw in the front part
and then put in the cotter pin

Hi waiting for Parts from the OCC for the last steps on the TA found some parts in my garage bought some month ago made the rod for the brake master cylinder so i will not have any problems to take it off took all measurment from the original took a M8 nut a m10 nut a 14 mm round steel for the front...

Hi
and what plugs for a Laystall head ?
the same?

THX Steve have a bad cold so just a few minutes in my garage in the basement not too cold but upstairs by the fire is much better time to read and watch videos on the web the BMC was installed a few days ago I wanted to put the fluid in and fill the system with my son but nothing happens no pumping ...

When you make a mistake, you have to find another solution. so i took the other steering and put it together sector in the middle and drop arm in position, this one also has a punch like the drop arm and if you look over the edge of the steering body you can see that it is the centre of the drop arm...

thx for this post
now i know why my wiper motor doesn t work
only one wire
i won t drive the car in rain, so in the past it doesn t matter me,
with this information i can solve the next problem of the car

next small mistake haven t marked the new sector didn t know it but i have exactly two turns from left to right so from the left to the middle is 1 turn with this picture i hope i find the right position that are the small things what you have to know haven t seen the marks there are no marks on the...

i have a little cold in the moment, time to read a lot today the fluid grease i had ordered arrieved, have ordered at 01.01 grrrrrr EUROLUB 708900 Schmierfett Gearfit EP 00/000 900g so i took my painted and assemled steering with the new sector shaft, new roller bearings and the brass tube with some...

Hi with the help here and mgexp it is possible to do nearly all on this little cars i haven t done a engine rebuild but i would do it have done so much different work on my car, some trouble ok, but at the end it was always much better then before if you do it yourself , you see the problems and you...

not the only thing wrong with this car ;-) this nuts came with teh car good that I waited to order from the Octagon Club now all brake drums are installed first step before installing the drums is to test the exenter you can see work of them perfectly without the drums close the exenter install the ...