Hi
good luck for 2023

the second picture shows how it was previously assembled
half of the broken spring to the left of the ball, the other half to the right and the screw was so tight that no movement was possible

i hate it if i don t understand it i hate it if i can t get parts out so now it is out and as i thought the other half broken spring was on the other side i made 2 pictures one with the broken springs on both sides, no play nothing, wasn t possible to turn the ball anywhere the difference betwenn DL...

Sorry Look what they did to the steering of my car in the past taken off the DLE the ball could not turn, the screw was so tight that there was no play, nothing was hard to open and what I found you can see on the picture the ball has the shoulder so it is not possible to take it out as it should be...

Hello again totally confused, just read this article in ttype.org https://ttypes.org/tc-steering-understanding-end-assemblies/ there Doug Pelton an MG specialist explains "There are 4 end assemblies here. 3 tie rod ends and 1 steering arm end" "The tie rod ends (TRE) have a cross slot (X) in the end...

so another mistake in the past with a big impact
no wonder there were so many track rods in the box
always wrong ones
spring again spring does not work
i think nor only my car has this problem ;-)

ok ! only the one on the drop arm is different, i have noticed it have made a illustration of it, a little bit different as Jim Buell has illustrated it and now i understand it, the arrows are not the same as the words... i hope i am right and i found, in the past there was a mistake on my car . i h...

what shoud i do waiting for the new year i went to the garage :bow: taken off the last parts from the stearing found 3 new tie rod ends found a tool to get the old one out then i made it hot with a flame to loosen the nuts all tie rod ends including the ball where ok, but i will take the new ones no...

Hi thanks for all the help i got here have done the job some days ago ;-) https://www.mgexp.com/forum/t-series-and-prewar-forum.46/mg-ya-no-1675-from-1948.4022768/page-27 bearing, 2" Socket and some more ordered will come next year all a good wish, health, peace and luck for 2023 Regards Franz :thum...

first i have to understand all of it just found this here https://www.limora.com/de/messingbuchse/23432/ this part is in it look to the picture the halfshaft is nearly polished at the end where the brass sleeve it sitting I will replace the bearing here with this one: 1 piece SKF deep groove ball be...

Should have opend it before
Here a picture
Need a new paper seal
Modern nut with sleeve inside

time to search the web left rear brake was wet, first i thought it is break fluid, but all cylinder and rubber was ok so oil ?! what tool do you use to open the nut there ? someone with experience with this part ? also i have to change the gearbox mounting, left side jelly, right side much better i ...

Today first painting from the egine to the back Also i prepared the brake cylinders wirh the new rubber, works perfect Also cleaned the Brass parts and some others parts Have to clean the garage again, thus dort horrible. Will see what kind of seal Brown and gammons will sent me. One more paint tomo...

Thanks Steve now one other important step dismanteling the brake cylinders one was a little bit hard to dismantel, so really good that i have done it now now all off them are looking like new, all pistons are ok the rubbers looks ok, but i have new one, so i will change all the garage is cleaned up ...

ordered a sector shaft, was the last, called there, he looked backwards
a few washers and shims
also the seal
safety first

frame cleaned and grinded. only a few rust, painted with fertan now, can paint it tomorrow have asked a friend for somthing like this here, answered in a minute, will come tomorow: https://www.ebay.de/itm/174431897349?mkevt=1&mkcid=1&mkrid=707-53477-19255-0&campid=5338353465&toolid=20006&customid=s%...

I don't know if I understood the backlash of the screw and the sector correctly. As I understand it, the sector should be pressed through the cover onto the screw to reduce the clearance ( red arrow in my picture ) there should be clearance between the sector and the housing ( black arrows ). The pr...

have taken some pictures to the place where the seal should be on my steering there ist the needle bearing with a seal , i hope you can see it, on the other one there is the original ? seal but if i take a measurment there is a little difference made a picture to explain it not perfect drawing, i am...

Thanks, what seal on the sector shaft today, i think they had problems in the past with leaking so they use the grease. that should be the right oneß https://www.rudolfs-oldtimershop.de/shop/index.php?id_product=3064&rewrite=sae-250600-q1&controller=product or this here https://www.limora.com/de/pen...

i am glad i opened both boxes the welded one is for the .... I have to buy a new one but the second one I cleaned and looked at again I took some more pictures, I don't think it's broken, it just looks like it is i think the reason is the picture i took and the scratch there but the edge of the box ...

hours later, half of the frame is ready for painting
seems to be all ok in the back