banjo-bolt-round-head

Discussion of TABC-related matters
Post Reply
User avatar
Franz Tenbrock
Posts: 539
Joined: Wed Jul 11, 2018 9:39 am
Location: Waltrop Germany

banjo-bolt-round-head

Post by Franz Tenbrock » Sat Aug 04, 2018 10:51 am

https://abingdonspares.com/products/ban ... ad-2-bolts

Hallo
now my fuel line is ok
new oil is in the engine
new spin on oil filter
new pressure line to the gauge

but i want to turn around the oil line from the block to the head
but at the block there ist a round banjo bolt and i dont know how to open it

a special tool available ?

moos internet says the hex one is only for the late TD and TF
Best Regards
Franz

3D Print: CJR3 case for Lucas340, individual Titan-X spark plug holder, resin printed octagon hazzard light switch and some more,

User avatar
frenchblatter
Posts: 625
Joined: Wed Apr 01, 2015 1:22 pm
Location: Royston, South Yorkshire
Contact:

Re: banjo-bolt-round-head

Post by frenchblatter » Sat Aug 04, 2018 9:26 pm

Franz, look carefully, it has two flats each side for a spanner, or it should have.Fr
Lynne & Norman Verona.

Our website

Visit our website to see what this idiot gets up to in his retirement

User avatar
Franz Tenbrock
Posts: 539
Joined: Wed Jul 11, 2018 9:39 am
Location: Waltrop Germany

Re: banjo-bolt-round-head

Post by Franz Tenbrock » Sun Aug 05, 2018 7:45 am

ok
with picture it will be easy to see what i mean

the car is new for me, someone has done it like it is in the photo
it is wrong
the engine is a XPJMi

the bolt there is difficult to open, so i ask here

my pressure in the gauge is to low, it is about 35 psi
the line to the gauge is new, but it is at the head like it it in the photo

i want to change it to the block, but i don t know how to open

i will be carefull so i ask here
Attachments
banjo bolt.JPG
Best Regards
Franz

3D Print: CJR3 case for Lucas340, individual Titan-X spark plug holder, resin printed octagon hazzard light switch and some more,

User avatar
Franz Tenbrock
Posts: 539
Joined: Wed Jul 11, 2018 9:39 am
Location: Waltrop Germany

Re: banjo-bolt-round-head

Post by Franz Tenbrock » Sun Aug 05, 2018 8:17 am

after i have written an idea come to my brain ;-)
i go to the garage and ....

i hope it will work

tomorrow i will order a new banjo bolt for the block
than we will see
Attachments
Spezialnuss 2.JPG
Spezialnuss 2.JPG (24.66 KiB) Viewed 4890 times
Spezialnuss 18.JPG
Spezialnuss 18.JPG (29.58 KiB) Viewed 4890 times
Best Regards
Franz

3D Print: CJR3 case for Lucas340, individual Titan-X spark plug holder, resin printed octagon hazzard light switch and some more,

User avatar
Franz Tenbrock
Posts: 539
Joined: Wed Jul 11, 2018 9:39 am
Location: Waltrop Germany

Re: banjo-bolt-round-head

Post by Franz Tenbrock » Wed Mar 13, 2019 9:08 am

Hi
so today , realy bad rain outside, i had time to do the oil line,
my special tool works perfect,
i took off the oil line to change the gauge line from the top to the bottom
in the past when they had done it they took wrong banjo bolt ?

the fine banjo bolt was at the bottom , it has the round head, so i need my special tool
i put it back at this place after turn around the line
at the top at the laystall head there was the other bolt, i think not the right one, i took it again , and hope it will go.

than i start the engine,
and
big surprise, the oil pressure was 35 before change the line, now 65

so it is realy important where the oil gauge line fit, it should be at the bottom

last year i was realy afraid ....
Attachments
banjo bolt.JPG
banjo bolt.JPG (31.64 KiB) Viewed 4028 times
Best Regards
Franz

3D Print: CJR3 case for Lucas340, individual Titan-X spark plug holder, resin printed octagon hazzard light switch and some more,

User avatar
Mitchman2
Posts: 31
Joined: Sun Mar 25, 2018 6:07 am
Location: North Carolina

Re: banjo-bolt-round-head

Post by Mitchman2 » Fri Mar 15, 2019 6:24 am

Yes, gauges read best when close to the source.
Mitch

1930 Model A Ford (owned since 1972)
1948 MG TC Special
1958 MGA
1966 E-Type OTS (just like the one I had in HS back in '74.

User avatar
Franz Tenbrock
Posts: 539
Joined: Wed Jul 11, 2018 9:39 am
Location: Waltrop Germany

Re: banjo-bolt-round-head

Post by Franz Tenbrock » Fri Mar 15, 2019 12:42 pm

Hi
now i know it,
but i have read a lot here and in one other forum, some people say it doesn t matter where it is.
I have the car driven 6 month, every time afraid i damage the engine,
is there sombody who knows the original thread of the banjo bolt for the laystal head. the bolt they used for my car isn t the right one. but in the moment it works, some day i will prepare the thread and take the right one.
a lot of little problems to solve before.
Best Regards
Franz

3D Print: CJR3 case for Lucas340, individual Titan-X spark plug holder, resin printed octagon hazzard light switch and some more,

User avatar
cdrolshagen
Posts: 100
Joined: Tue Dec 29, 2015 1:30 am
Location: Soerup Germany

Re: banjo-bolt-round-head

Post by cdrolshagen » Sat Mar 16, 2019 1:56 am

Hello Franz,
the original thread type in a cast irion head is metric M10 x 1 mm, so I guess the thread in a Laystall head is the same,
cheers Carl

User avatar
Don Walker
Posts: 44
Joined: Mon Aug 01, 2016 3:16 am
Location: South Australia

Re: banjo-bolt-round-head

Post by Don Walker » Sat Mar 16, 2019 3:37 am

Hi Franz, the end result is the oil pressure is still the same!

User avatar
Franz Tenbrock
Posts: 539
Joined: Wed Jul 11, 2018 9:39 am
Location: Waltrop Germany

Re: banjo-bolt-round-head

Post by Franz Tenbrock » Sat Mar 16, 2019 4:57 am

no
it isn t the same
before the turn around it was max 38
i was in the garage 10 minutes ago, done the last work before starting
now it goes up tu 80,
nothing done else, only change from the top to the bottom of the engine, to the original position
before i fit it again, i check the pipe, it s open for the oil, nothing damaged
Best Regards
Franz

3D Print: CJR3 case for Lucas340, individual Titan-X spark plug holder, resin printed octagon hazzard light switch and some more,

User avatar
Steve Simmons
Site Admin
Posts: 2635
Joined: Wed Dec 26, 2012 10:48 am
Location: Southern California
Contact:

Re: banjo-bolt-round-head

Post by Steve Simmons » Sat Mar 16, 2019 9:19 am

The physical pressure will be the same, but indicated pressure will be higher and more true to actual pressure at the lower fitting.
1949 TC8975 / XPAG 9609
1948 TC6011 / XPEG1182 (XPAG6472)
http://www.mgnuts.com

Post Reply