CLASSIFIED ADS
from and for members of the "T-ABCs Forever-Club"
Please send your ads to Jim Shade, West Covina, CA, USA, fdshade@aol.com
or to Walter Prechsl, Obersulm, Germany, walter@mg-tabc.org
=======================================================================
FOR SALE
-----------------------------------------------------------------------
Shorrock C75 supercharger for sale, excellent condition, complete with carb &
top pulley to suit MG, Mini, Austin, etc. Offers. Located in England.
Call Steve on +44 (0) 7855777721 or
at steve.wright(at)rbs.com 2/08
-----------------------------------------------------------------------
1938 TA Tickford 3079 MPJG 3119 for sale
I just try to sell my 1938 MG TA Tickford. All numbers matching car,
runs and drives excellent.
1948 TC (1949) for sale
TF 1500 (1955) for sale
For sale exclusive 1934 MG PA Police car, manufactured in Lancashire, UK,
with special reverse doors, its a #5 of 20 ordered by the Lancashire police.
This MG #0411 is fully complete, with extensive documentation history of awards.
Fully restored
Ramasauskas, Zilvinas, Lemont, IL, USA
ramasauskas(at)sbcglobal.net 1/08
-----------------------------------------------------------------------
Original MG Midget Instruction Manual (series TA and TB).
I believe its 1939. The contents are in very Good condition, some
dirt/grease marks on the cover. And it even has the Flying Standard
Eight & Ten 1939 Maintenance Wall Chart.
Interested? Please send an offer.
Paul Linton, paulwlinton(at)hotmail.co.uk 10/07
-----------------------------------------------------------------------
TRADE a TA for a TC: I have what I believe is TA1560 (EAE 250), 1936 or 37 with
partial provenance. Engine is Morris MPJM2A. It had a complete mechanical rebuild
3 years ago, paint and body, interior sometime prior to that. Recently I had the
speedo/tach rebuilt by Nisonger, new tires and battery, restored the pre-war headlights
and tail light. I'd be willing to trade it for a TC in excellent shape, documented
mechanical history and chrome wire wheels.
Lets talk; Dale.hamilton(at)med.va.gov.
Dale Hamilton
-----------------------------------------------------------------------
TA Spares
Various new spares (e.g. 8:39,7:37 CWP, sidelight, conrods, brake cylinders,
pistons, etc.) and secondhand parts (e.g. exhaust manifold, starter motor,
rear wings v.g.c., original headlamp rims, glasses, dipping reflectors, etc.).
Send for full list davejheath(at)yahoo.co.uk
David Heath 4/2007
-----------------------------------------------------------------------
ALTETTE HORN REBUILD KITS
The kits consist of 6 chrome acorn nuts, 4 short 1BA studs, 2 long 1/4"
bsf studs and 4 gaskets. All the parts required to rebuild the various
models of Altette horns as used on TA TB TC. Cost $30 US includes air post
to anywhere in the world.
Contact John Hancock mg.john.brenda(at)actrix.co.nz 8/2003
-----------------------------------------------------------------------
TC seat with spring core, handmade on special order for a better seat
suspension and support of the backbone.
only to tack down to the base board and put over of the leather cover.
50 euros + postage (probably too expensive for outside europe)
Walter Prechsl, Obersulm, Germany
+49-7130-46064 walter(at)mg-tabc.org
-----------------------------------------------------------------------
Permanent Offers
-----------------------------------------------------------------------
MG TC Foot Pedal Spring Set
There are 4 items included: brake pedal return spring, brake switch return spring with
pedal hook, and clutch pedal return spring. These are new springs. The hook is made to fit
and replicate the original. The ends of the springs may need a little adjustment at install
for the custom fit to your car. Don't bother chasing to the hardware store
and trying to locate these . . . they either don't fit, are too stiff. I have done all that
and don't wish it on anyone. This set is your simple solution.
Cost is $21. Instructions and diagrams are included. Items will be mailed priority
mail in the US for $6.00 shipping and handling and Canada for $11.
Outside N. America, shipping and handling will be $13 to most countries.
Outside the US payment can be made through paypal, dougpelton(at)cox.net
Please email with any questions.
Doug Pelton, 3754 E Nance Circle, Mesa, AZ 85215, +1-602-690-4927
-----------------------------------------------------------------------
XPAG-XPEG Roller Lifter Camshaft Kits. No lifter wear. Custom ground for each
application. Complete kit, Camshaft 8620 steel, Lifters, Pushrods, & state of
the art 2 piece valve springs > $1300.00.
Len Fanelli 356 East Grassy Sprain
Rd. Yonkers, N.Y. 10710-2308, phone +1 914 420 8699
Email laf48(at)aol.com 4/2008
-----------------------------------------------------------------------
New crown wheel and pinion for MG TC rear axles 8:43
As a new part from german manufacturing in limited amount offered.
Made in Germany from modern steel, hardened and grinded this diff is the ideal
optimization for a TC with 5-gear conversion. this new crown wheel and pinion
can be mounted without any modification in the opriginal pumkin housing.
(the original rear axle transmission ration at the is TC 8 : 41)
Though the saving from the 5th gear is reduced somewhat, but the TC becomes more
lively. All gear´s ratios are shorter herewith. The car speeds up better and
has a much better hill climbing behaviour and the 5th gear brings a very high end speed
at faily low revs. The revs in gear 5 at 63 miles (100 kmh) are 550 revs lower as
in gear 4 with original crown wheel and Pinion.
8 set are still available, the price is 974,- Euro (= 1180,- USD)+ pp
more technical infos here
Manufacturer: Manfred Jäger => his TC
contacts please via walter at walter(at)mg-tabc.org
-----------------------------------------------------------------------
KLG or LODGE spare spark plug holder
Available in 4 or 6 plug configurations. Marked MG inside an octagon at one end,
the other end has LODGE or KLG plug information. These are color cast in modern
materials from restored originals in the same BAKELITE brown color. 4 plug = USD$40,
6 plug =USD$45 plus mailing cost from Colorado, USA.
Please contact Ben Cordsen at sculptart(at)aol.com
-----------------------------------------------------------------------
MG T SERIES PARTS AND SERVICES Prices in CDN$ June 2007
TA/TC front steering knuckle stub axle inserts with ¾"-16 tpi thread, $48.00 each side.
Use MG TD/TF/MGA stub axle nuts.
TA/TC Stub axles supplied and installed in your steering knuckles @$175.00 each side. Insert threads
are ¾"-16 tpi, use nuts from MG TD/TF/MGA.
TB/TC/early TD oil filter adapter for modern spin-on-$105.00
TF/late TD oil filter adapter for modern spin-on-$70.00
TA/TC Tompkins steering box cover kit 82.00
TA/TC steering worm and peg $380.00
TA/TC tapered rear axles with key and nut ( you taper bore your hubs ) $175.00 each (available TC
6 spline or Morris Minor 10 spline).
TA/TC new rear hubs taper bored for the above axles -$230.00 each.
TA/TC new front hubs -$212.00 each.
TA/TC new rear wheel bearing securing 2" hex nuts with lip seals and keeper washers-$70.00 the set.
TA/TC Alfin brake drums- $1,166.00 $ a set
TD/TF alfin brake drums, $1,220.00 a set.
TA/TC new high ration crown wheel and pinion gear set, 4.625 ratio-enquire.
TB/TC rear gearbox steel reinforcing plates, pre-drilled ready for installation. Some studs and spacers
required. $37.00
TA/TC/MMM Dual Spare wheel adapter, ( uses original lock-nut )- $175.00
TD/TF wire wheel front hubs- $185.00 each
TD/TF wire wheel rear hubs-$212.00 each.
TD/TF new brake master cylinder - $200.00 .
XPAG/XPEG Light steel racing flywheel-$575.00 Suitable for TC or TD with 7 1/2" heavy duty diaphram
clutch cover. Use original starter and applicable 7 ¼" ring gear.
I have a limited number of MG colour art prints which I obtained
from the original artist. The prints are black TA Tickford, green TC,
black TD and red TF. The original artwork was done in the late
sixties/early seventies by Will Davies, a Toronto Ontario artist who owns
an MG TC. The prints were taken from these drawings. The prints are on
high quality paper suitable for framing. Overall paper size is 11 3/4" x 16
1/4" with the art work size being 9 1/4" x 14 1/4".
MG T Series Art Prints, Set 4 prints, TA Tickford, TC, TD, TF, size 14" x 18" mat, $25.00
All prices are in CDN$ with shipping extra.
Bob Grunau
150 Pinewood Trail,
Mississauga, Ontario, Canada, L5G-2L1,
+1-905-274-4136 or email grunau.garage(at)sympatico.ca
-----------------------------------------------------------------------
MG "TABC" and Prewar hand brake re-chrome kit. This kit enables you to
renew that tatty hand brake lever that you forgot to due 20 years ago. the
installation is simple and allows you to install without removal from the
car fits all T series (not TD/TF) and Prewar cars. High quality chrome on
brass.
Cost is 55.00 plus shipping NYS sales tax if in NY.
JoeCurto(at)aol.com, phone +1-718-762-7878 Ph.
Do not send CC number over internet 9/2000
-----------------------------------------------------------------------
Dash Panel Lettering Kit
STARTER MIXTURE FOG PANEL SLOW OVERDRIVE (IF WANTED)
PULL PULL LAMP SWITCH RUNNING
Application is done directly to the dash panel eliminating the need to
remove the panel to screen print the lettering. The lettering is printed on
a very thin, adhesive backed mylar with a matte clear over laminate that
is very easy to apply.
The lettering is also available in black for later TCs with copper
colored dash panels. The lettering is not applied individually but rather as
a complete section. For example STARTER PULL is done in one piece with the appearance
of being die cut.
Cost per complete set as outlined above is $33.50 including postage.
Add $5.00 for OVERDRIVE if wanted. Please note preference of black or white
with your order.
Please send check or money order payable to
Paul Pothier at 73 N. Hayden Parkway, Hudson, OH 44236 USA.
pothier39(at)email.msn.com 2/2001
---------------------------------------------------------------------------
NEW LED 'D' LAMPS
Upgrade your TC Tail lights with modern LED light power! These are two function
(Brake & Tail light + License plate) units that are simple to install in your
existing 'D' lights. Instructions included.
Reduced electrical load and much BRIGHTER, SAFER tail lights.
BE SAFE - BE SEEN
p/n ST51D12VPG Positive ground $ 85.00 ea Plus Shipping
p/n ST51D12VNG Negative ground $ 85.00 ea Plus Shipping
3' x 5' MG flags for sale at -- check it out!
order from Terry Sanders, Oakland, CA
email TATerry (at) pacbell.net
Payment via PayPal at TATerry (at) aol.com or check/MO
---------------------------------------------------------------------------
 |
|
Black Hard Rubber Color Restorer
Now you can bring back the deep black color and luster your black hard
rubber dashboard knobs and switches once enjoyed when they were young
and perky by using Pensbury Manor's GREAT KNOBS! to reblacken the oxidized,
faded and browned out color that time and exposure to the elements has
caused! GREAT KNOBS! comes in 1 and 2 oz. bottles - enough to restore
from 25-50 normal size knobs and switches.
$12.00 resp. $23.00 + s&h
more information at:
www.pensburymanor.com/Pensbury_Garage.html
|
| Syd Saperstein, Pensbury Manor 22 Saratoga Lane Alamo, CA
94507, tcsyd(at)sbcglobal.net |
---------------------------------------------------------------------------
WANTED
--------------------------------------------------------------------------
WANTED
I require the casting that takes the right hand front spring shackle on chassis dumb
iron for TC.
Tony Lyons-Lewis in South Africa at lionsden (at) netactive.co.za 4/2008
--------------------------------------------------------------------------
WANTED
TC parts: fuel tank and straps, radiator cap, bonnet centre strip, 4" x 16" (19" also)
wheels (rims only required), windscreen frame (have glass), windscreen wiper motor and
blades, rear vision mirrors, gear lever knob, accelerator pedal, headlamp glass (1948-type),
driving lamp, false nose , engine hood locks, door locks, strikers & hinges, hood bows,
hood fabric, tonneau & interior trim (vellum beige), seat squabs, seat back (complete),
steering wheel (Brooklands) with mounting clamp, body piping (Clipper blue), carpet set
with MG rubber insert, instruments and switches, clutch return and other light springs,
clutch driven plate, clutch thrust race, exhaust manifold, inlet air cleaner manifold and
cleaner, oil filters, alloy sump. Anything of interest for the TC will be considered.
Peter Finlay TC7346 Australia
peter(at)finlays.com.au Tel: +61 2 9873 1773 1/2008
--------------------------------------------------------------------------
WANTED
To suit J75 Marshall supercharger, aluminium castings (or patterns) for
nose extension, carby manifold and head manifold to suit XPAG TC belt drive
installation.
Any bits or info greatly appreciated.
Harry Pyle hdpyle(at)bigpond.net.au 5/2005
-----------------------------------------------------------------------